2016+ Hi-Clearance Rear Bumper w/ Dual Swing Gate

Status
Not open for further replies.

Pelfreybilt

pelfreybilt.com
T3G O.G.
Messages
108
T3G Member
#208
We are certainly working on it! Finishing up a few projects first, but it's coming soon :)

Here are a few renderings of the Toyota Tacoma Dual Swingout Rear Bumper. Feel free to email michael@pelfreybilt.com if you want an ETA based on the options and accessories you're looking for.

www.pelfreybilt.com



 

Tyler

= IX • Paragon
Badministrator
T3G O.G.
Messages
5,977
Location
Long Island, NY
First Name
Tyler
Military
Marine Corps (Vet.)
Build Thread
(Click to View)
T3G Member
#1
We are certainly working on it! Finishing up a few projects first, but it's coming soon :)

Here are a few renderings of the Toyota Tacoma Dual Swingout Rear Bumper. Feel free to email michael@pelfreybilt.com if you want an ETA based on the options and accessories you're looking for.

www.pelfreybilt.com



Will there be an option to have only the tire swing gate on the bumper?
 

Tyler

= IX • Paragon
Badministrator
T3G O.G.
Messages
5,977
Location
Long Island, NY
First Name
Tyler
Military
Marine Corps (Vet.)
Build Thread
(Click to View)
T3G Member
#1

SD_Taco

= III • Silver
T3G Supporter
T3G O.G.
Messages
52
Location
San Diego
First Name
Jay
T3G Member
#35
Awesome can’t wait! Currently have my spare tire in the bed which I hate. I’ll email Michael for an ETA. Thanks!
 

951_yota

= V • Platinum
T3G Supporter
Messages
327
Location
Socal
First Name
Travis
Military
Air Force (Vet.)
T3G Member
#405
Got my HC on order from them! No tire mount im keeping it under in stock. Now to be brave enough to cut the bedsides :eek:
 

i8boots

= II • Bronze
Messages
23
Location
UT
First Name
Bryan
T3G Member
#431
A bit off topic, but if someone came out with a front slimline bumper, or hell, a full bumper, that stuck out LESS than the stupid fat lip currently on the Taco, I'd probably go into debt to acquire it.

Similarly, if I could get this rear bumper sexiness but still be able to use my rear sonar (has saved me from a lot of accidents, I'm bad at cross traffic), I'd probably jump on it as well.
 

Tyler

= IX • Paragon
Badministrator
T3G O.G.
Messages
5,977
Location
Long Island, NY
First Name
Tyler
Military
Marine Corps (Vet.)
Build Thread
(Click to View)
T3G Member
#1

mh.meier

= VI • Diamond
Messages
370
Location
Socal
First Name
Mike
Military
Marine Corps
T3G Member
#600
Hey guys here is a list of all the options that come standard on the bumper. Just anted to collectively store it here as I have gotten a lot of emails asking about the options on the bumper. Price is set to be approximately $2200.00 for the powder coated version and less for the non powder coat version (Price is not SET but this is a close approximation)
-Dual swing arms (we will not do a single swing arm version)
-Fold down table (passenger side, inside the gate)
-Dual antenna mounts
-Hi-lift mount
-Reverse light cutouts (they come with filler plates if you don't run lights)
-Spare tire carrier
-Back up camera relocation (for the stock camera)
-Flip up license plate mount
-Hidden receiver hitch (you will need to remove the stock hitch to install the bumper)
-(2) mounting plates that allow you to mount a combination of any 2 mounts we offer (propane, CO2, NATO can, Rotopax (sold separately))
-Proximity (back-up) sensor cutouts (fillers provided for those without)
-Completely sealed bearing units (no maintenance required)
-Lockout pins (to keep the bumper from opening too far) with internal locking mechanisms so even if they break the only open so far

We don't have an exact weight yet, but estimate it to be around the current second generation Tacoma swing out bumper at about 180-190# for the hi-clearance version and 135-145# for the standard version. Once in production they will have at least a 12-14 week lead time (initially) until we can get production down! I do have about 7 pre-orders currently but we have not done a forum one yet so if there is enough interest in a pre-order we can start one on here.

This would include:
-Receiving the bumper before anyone else (typically a few months before)
-Reduced price depending on the number of pre-orders (to be determined)
-A Special item included (working with Tyler from 3G on this
-Reduced cost on the carriers that attach to the bumper
-Only requires a deposit of 1000.00


Let me know if you guys need any more details!
 
Status
Not open for further replies.
Top Bottom